0.2 mL PCR Tube Separation Racks
Permagen offers an extensive line of PCR tube separators. They all feature the following benefits
- Strong NdFeB magnets for rapid bead separation
- Angled holes allow PCR tubes to come close to magnets for maximum efficiency and easy aspiration
- Solid aluminum design for durability and consistent results
- Rubber feet to help prevent sliding around on bench
- Made in the USA
MSR812
- Aluminum alloy design for years of trouble-free use
- Fast magnetic bead separations
- Held to tighter tolerances for more consistent results
- Pulls beads to side of wells for easy tip tracking down front side
- Rubber feet to help prevent slippage
- Stable design
- Angled tube holes which allow the tubes to come close to magnets
- Each tube has its own magnet
- Up to 24 Individual PCR tubes
- Up to two, 8-strip PCR tube strips
- Up to two, 12-strip PCR strips
- Any Magnetic Beads
Maximum – .2 mL
Minimum – 30 µL
0.2 mL PCR Magnetic Separator 24-tube
Permagen’s 0.2 mL PCR Strip Magnetic rack is designed for magnetic bead separations from Individual tubes, 8-strip, or 12-strip PCR tubes
Accommodates any common PCR strips or individual PCR tubes
Tubes are angled and beads will be pulled to back wall allowing easy aspiration and tip tracking down the front wall of the tubes without disturbing bead pellet
MSRLV08
- Two racks built into one
- 50 µL – 0.2 mL volumes on one side
- 5 µL – 50 µL volumes on opposite side
- Sides are conveniently marked with volume recommendations
- Fast magnetic bead separations
- Held to tighter tolerances for more consistent results
- Pulls beads to side of wells for easy tip tracking down front side
- Rubber feet to help prevent slippage on both sides
- Stable, solid aluminum design
- Angled tube holes which allow the tubes to come close to magnets
- Up to 16 Individual PCR tubes per side
- Up to two, 8-strip PCR tube strips per side
- Any Magnetic Beads
Maximum – .2 mL
Minimum – 5 µL
0.2 mL Dual Volume PCR Strip Separator
MSR402
- Aluminum alloy design for years of trouble-free use
- Fast magnetic bead separations
- Held to tighter tolerances for more consistent results
- Pulls beads to side of wells for easy tip tracking down front side
- Rubber feet to help prevent slippage
- Stable design
- Angled tube holes which allow the tubes to come close to magnets
- Easy protocol integration from our MSR812 rack
- Up to 32 Individual PCR tubes
- Up to four, 8-strip PCR tube strips
- Any Magnetic Beads
Maximum – .2 mL
Minimum – 30 µL
32 X 0.2 mL PCR Strip Magnetic Separator
Permagen’s 32-tube PCR Separation rack features all of the same aspects of our MSR812 rack above for easy protocol transition for labs wishing to scale up to four PCR strips at a time, or up to 32 individual PCR tubes.
Features include solid aluminum alloy design with hard coat finish for years of trouble-free use, rubber feet to help prevent slipping on work bench, less tippy than common plastic products, and fast separations using any magnetic beads
MSR1224B
- Aluminum alloy design for years of trouble-free use
- Fast magnetic bead separations
- Held to tighter tolerances for more consistent results
- Pulls beads to side of wells for easy tip tracking down opposite side
- Rubber feet to help prevent slippage
- Stable design
- Angled tube holes which allow the tubes to come close to magnets
- Most 1.5 mL Microcentrifuge tubes
- Some 2.0 mL Microcentrifuge tubes
- 8-strip PCR tubes
- 12-strip PCR tubes
- Individual PCR tubes
- Any Magnetic Beads
Maximum (PCR Tube)– .2 mL
Minimum (PCR Tube) – 10 µL
_____________________
Maximum (1.5 mL Microcentrifuge) – 1.5 mL
Minimum (1.5 mL Microcentrifuge Tube) – .5 mL
0.2 mL PCR Strip / 1.5 mL Microcentrifuge Tube Separator
Permagen’s 0.2 mL PCR / 1.5 mL Microcentrifuge tube separation rack is designed for labs with both PCR strip and 1.5 mL separation protocols. On the top, hold up to two of either 8 or 12 strips, or up to 24 individual tubes. Flip over and hold up to twelve 1.5 mL Microcentrifuge Tubes
Features include solid aluminum alloy design with hard coat finish for years of trouble-free use, rubber feet on both sides to help prevent slipping on work bench, less tippy than common plastic products, and fast separations using any magnetic bead
NEW – Now comes with a snap-on end piece for 15 & 50 mL Centrifuge tubes